We make sure to use high-quality equipment and toilet repair parts that help ensure optimal functioning. If you have a running toilet or any other plumbing issues or emergencies in San Bernardino County, contact us online or give us a call at and we'll fix the problem for you right away. Water heaters get a serious workout around the home.
Adhering to a regular maintenance schedule can Toilets that keep running may have one of the following problems: The float height needs to be adjusted The flapper is leaking and needs to be replaced The refill tube needs to be shortened Tools and materials you may need: Rubber gloves Replacement fill valve Toilet replacement parts Multi-bit screwdriver Cutting pliers We strongly advise that you contact an expert plumber to inspect the situation for you, as there could be other issues with your toilet that may need repair and maintenance.
You Need to Lower the Float Among the most common causes for a running toilet is overflow water leaking down into the bowl from the tank via the overflow tube. The Flapper Is Leaking and Needs Replacing Perhaps the most common reason for a running toilet is an old flapper that needs to be replaced. You Have to Shorten the Refill Tube Another cause behind your running toilet could be that the refill tube is always pumping water into the bowl, and this happens when the tube is too long and isn't positioned properly in the overflow tube.
Related Posts. Mar 30 Water heaters get a serious workout around the home. View Article. It's designed to prevent the toilet tank from overflowing if the fill valve does not turn off.
There are several reasons why the water may be flowing into the overflow tube and causing the toilet to run. The water level inside the toilet tank should always sit below the overflow tube and the fill valve to ensure that the water doesn't continuously flow into the tank and out through the overflow tube.
Check the water level by removing the lid from the tank of the toilet and verifying whether or not the water level is too high, causing it to run into the overflow tube. If the water is running into the overflow tube, then the water level may need to be lowered, but if the water is not running into the overflow tube, then the issue is likely with the flush valve.
To lower the water level inside the toilet tank, you will need to adjust the float rod or float cup. A float rod can be identified by the horizontal rod extending from the fill valve to a float ball, while a float cup is a small cylinder that wraps around the fill valve and slides up or down with the water level.
You will need to locate the screw that attaches the float rod or float cup to the fill valve. Use a screwdriver, a set of channel locks, or pliers to turn this screw about a quarter-turn counterclockwise to lower the water level. Continue making adjustments until the water is no longer flowing into the overflow tube.
If the water continues flowing, regardless of the position of the float rod or float cup, the issue is likely with the fill valve. However, if the water stops flowing, but the volume of water inside the tank is not enough to properly flush the toilet, then it's likely that the overflow tube is too short for the toilet. Water-logged floats can also cause constant running. If water is trapped inside your float, it will sit lower in the water and leave your float valve partially open.
Check your float by unscrewing it if applicable and shaking it. Replace the float if you hear water inside. An overflow tube is intended to prevent the toilet tank from overflowing, but if it's too short, then the water will continuously flow into the tank and out of the overflow tube.
This can occur if the flush valve is not compatible with the toilet, or if the overflow tube was cut too short during installation. If the overflow tube is too short, the only way to fix this issue is to replace the flush valve. Just make sure that the new flush valve is compatible with your toilet and that the overflow tube is taller than the old overflow tube to prevent water from draining continuously. The flush valve is an assembly within the toilet that consists of an overflow tube, tank-to-bowl hardware, a tank-to-bowl gasket, a flapper, and a chain that connects to the flapper.
The main purpose of a flush valve is to open the flapper to allow water to flow into the toilet bowl when the toilet is flushed and to close the flapper when the toilet tank is empty to allow the toilet tank to refill. A constantly running toilet is typically due to an issue with the flush valve assembly, so one of the first parts to inspect should be the chain and flapper. If the chain is too short, then it won't allow the flapper to close properly, but if it is too long it may get trapped underneath the flapper, causing it to leak.
Verify that the chain is just the right length to allow the flapper to fully close and open without a lot of extra chain. The next step is to inspect the flapper. These rubber parts can become warped, worn, or simply dirty over time and may not sit properly inside the flush valve seat.
If any defects are found in the flapper, then it's a good idea to replace it, but if it appears to just be dirty, then the problem may be solved by washing it with a water and vinegar solution. Just make sure to turn off the water to the toilet and drain the tank before attempting to clean the flapper. If the water from the tank continues to seep into the toilet bowl, or you find that the overflow tube is too short, then the entire flush valve will need to be replaced.
However, that doesn't mean that you can't inspect your own toilet and figure out if it's an easy fix. So without further ado, here are some things that you can do yourself to get your running toilet back to its regular operation. Safety First! Make sure you turn off the water supply line first at the shutoff valve or cutoff valve before performing any repairs.
Among the most common problems for a running toilet is caused by a fill valve issue. This is when the water level is too high and water spills out of the top tank and into the overflow tube then down into the toilet bowl. This happens when there is excess water in the top tank.
This can be fixed by lowering the water level or fill height by adjusting the height of the float ball. To get to it, the first step is to remove the tank lid. To lower the water level in the top toilet tank with the float arm or lift arm , make sure to loosen or tighten the screw until the float arm with the float ball or float cup drops to the right level.
To lower the water level in a toilet tank with a column float attached to the fill valve, loosen the screw or clip and then push down the float arm with the float ball to the right level on the fill valve and tighten everything back up again.
If the running stops, you have found your problem. Also, check that the float tank ball is not touching the tank wall. You could fix the issue but just making sure it isn't getting stuck on the sidewall. This will ensure the level is lower than the overflow tube and stop a running toilet. Fill valves are cheap and relatively simple to replace, so if this isn't working, replace the entire valve assembly. The second most common reason for a running toilet is a deteriorated toilet flapper valve or valve seal.
The flapper's job is to seal the water in the tank. When toilet flappers get too old, they don't seal the way they are supposed to , allowing water to continually pass from the toilet top tank down into the toilet bowl. To replace the flapper, remove the old one and replace it with a new one that you can purchase from any hardware store. You can remove it by detaching the flapper chain or lift wire and taking the flapper off the mounting pins on the side of the overflow tube.
Tip for DIY newbies: Drain all the water from the tank first before replacing the toilet flapper. You can do this by shutting off the water supply that feeds the top tank and then flushing the toilet to drain the remaining water.
Another Tip: If the chain is too long, it could be getting caught underneath the flapper as the tank empties. Your toilet could be running because the flapper isn't getting a good seal. So shorten it while you are in there poking around.
The third cause of your running toilet could be that the refill tube or overflow pipe is continually pumping water into the bowl. This can happen when the fill tube is too long and isn't positioned correctly in the overflow tube.
0コメント